Got some leftover parts from the old motor still taking up prime garage real estate, they're collecting more dust than cash offers. I dont want to scrap them due to the hard to find nature of some of the parts so they're free!
I will not deliver, if your local to Colorado Springs I might be able to meet if im out for a cruise otherwise you must come and pick them up... preferably in a rotary of some sort
S4 T2 dirveshaft (manual obviously, could use a coat of paint otherwise perfect)
S5 upper intake w/ throttle body and all sensors
S4 (i think) JDM lower intake (no EGR)
JDM OE top mouint intercooler (Says "Rotary")
S4 T2 coils (whole set w/ 8.8mm perf. wires)
S4 T2 Maf (with cone filter adapter plate)
Ill eventually have more but the rest is in storage, for now this is what I could easily find. As I said earlier the parts are free to any other rotary enthusiasts! Unfortunatly I will not "Hold" any of the parts for more than a couple days. Text me for any other info, Brett 7I9/322/443O
FC parts, need them gone!
FC parts, need them gone!
[SIGPIC][/SIGPIC]
winners compare their achievements with their goals,
while losers compare their achievements with those of other people.
winners compare their achievements with their goals,
while losers compare their achievements with those of other people.
- speedjunkie
- Senior Member
- Posts: 5281
- Joined: Wed Jan 02, 2008 9:14
- Location: Colorado Springs
- Contact:
It will work. I have a s5 tii tranny bolted to a s4 driveshaft, diff, and half shafts.
2003 MazdaSpeed Potege: Wiseco Pistons, Molnar Rods, Walboro 255, Megasquirt Ecu, Front Mount, Daily Driver.
1991 Mazda Rx-7 Convertible: Rebuilt 4-Port Turbo Block, TII drivetrain swap, Walboro 255, Megasquirt, Aeromotive FPR, JIC coilovers, 4" Stainless exhaust, Ticket Getter.
1976 Honda CB750F: Cafe Racer, Powder coated, Rebuilt, re-bearing/bushing, tapered stem bearing upgrade, Garage Project
2014 Silverado: Mazda Support Vehicle
2003 Subaru Forester: What was I thinking?...
1991 Mazda Rx-7 Convertible: Rebuilt 4-Port Turbo Block, TII drivetrain swap, Walboro 255, Megasquirt, Aeromotive FPR, JIC coilovers, 4" Stainless exhaust, Ticket Getter.
1976 Honda CB750F: Cafe Racer, Powder coated, Rebuilt, re-bearing/bushing, tapered stem bearing upgrade, Garage Project
2014 Silverado: Mazda Support Vehicle
2003 Subaru Forester: What was I thinking?...
found an incomplete engine o-ring kit! its technically for an 86-88 N/A but the vast majority of the seals will work on all
contents
(N326-10-B71) red water jacket seals x4
(N326-10-B72) black water jacket seals x4
(0839-10-455) tension bolt seals x18
(N236-14-604) oil metering pump o-ring x2
(0813-10-555) rear stationary gear o-ring x1
(N3A1-10-B73) dowel pin o-ring x4
(N231-10-174) front cover o-ring x1
(9954-10-1105) front hub bolt o-ring x1
(9954-10-1601) oil filter stand o-rings x2
(9954-10-3501) crank angle sensor o-ring x1
(9954-10-1252) injector diffuser o-rings x6
(N326-13-112) exhaust manifold gasket x1
(N326-20-305) EGR gasket x1
(N378-40-305) exhaust pipe gasket x1
The kit is incomplete due to missing upper and lower intake gaskets, 1 exhaust manifold gasket, and front cover teflon o-ring. I think the kit ran about $200 after shipping when I got it. All parts are from Atkins Rotary. I'd take $80 for the kit.
Ive also got a few Pineapple Racing blockoff plates for the EGR, ACV, and OMP, they only fit S4 N/A, theyll go with the kit too.
contents
(N326-10-B71) red water jacket seals x4
(N326-10-B72) black water jacket seals x4
(0839-10-455) tension bolt seals x18
(N236-14-604) oil metering pump o-ring x2
(0813-10-555) rear stationary gear o-ring x1
(N3A1-10-B73) dowel pin o-ring x4
(N231-10-174) front cover o-ring x1
(9954-10-1105) front hub bolt o-ring x1
(9954-10-1601) oil filter stand o-rings x2
(9954-10-3501) crank angle sensor o-ring x1
(9954-10-1252) injector diffuser o-rings x6
(N326-13-112) exhaust manifold gasket x1
(N326-20-305) EGR gasket x1
(N378-40-305) exhaust pipe gasket x1
The kit is incomplete due to missing upper and lower intake gaskets, 1 exhaust manifold gasket, and front cover teflon o-ring. I think the kit ran about $200 after shipping when I got it. All parts are from Atkins Rotary. I'd take $80 for the kit.
Ive also got a few Pineapple Racing blockoff plates for the EGR, ACV, and OMP, they only fit S4 N/A, theyll go with the kit too.
[SIGPIC][/SIGPIC]
winners compare their achievements with their goals,
while losers compare their achievements with those of other people.
winners compare their achievements with their goals,
while losers compare their achievements with those of other people.
Who is online
Users browsing this forum: No registered users and 98 guests