Attention All Rotorheads!

goldrocket · Postby **goldrocket** » Sun Nov 11, 2007 9:14

If there are any of you out there who have been searching for a competent, experienced rotary engine builder I just got off the phone with the guy who built mine. I am not an employee and i apologize if I am violating any rules of the board by posting this, but I had to research and spend weeks looking for someone who could build a strong performance rotary on a budget that real people can afford. I just want to share my experience with other like minded sickos who like lots of power from a wee little 1.3 or 1.2 liter engine. Here's the link:http://www.rotarywarehouse.com/index.php
I have over 7000 miles on my raceport 13b that was done for me and it runs smooth, makes a ton of power, and the oil doesn't even get dirty over oil change intervals. These guys do good work and it won't cost and arm, a leg and you first born to get your engine rebuilt correctly.
Just wanted to shre. Sorry, I can't seem to make the link insert option work right.

tsx_guy · Postby **tsx_guy** » Sun Nov 11, 2007 9:14

good fine sir, thanks for sharing. According to the CMZC's handbooks you have violated rule #1003.5
section 2 paragraph IV. As a result swift action will be taken. I have dispatched two thugs to break
your kneecaps and no they won't be gentle, have a nice evening j/k [img]http://coloradomazdaclub.com/forums/style_emoticons/<#EMO_DIR#>/laugh.gif[/img]

Stealth01 · Postby **Stealth01** » Sun Nov 11, 2007 9:14

<div class='quotetop'>QUOTE (6i_guy @ Nov 11 2007, 07:37 PM) [url=index.php?act=findpost&pid=10308]<{POST_SNAPBACK}>[/url]</div>

good fine sir, thanks for sharing. According to the CMZC's handbooks you have violated rule #1003.5
section 2 paragraph IV. As a result swift action will be taken. I have dispatched two thugs to break
your kneecaps and no they won't be gentle, have a nice evening j/k [img]http://coloradomazdaclub.com/forums/style_emoticons/<#EMO_DIR#>/laugh.gif[/img][/b]

The good news is that they will be driving a 6i, so they won't be able to catch you to break your knees, and if they do, just threaten to scratch their car. They'll get scared. [img]http://coloradomazdaclub.com/forums/style_emoticons/<#EMO_DIR#>/smile.gif[/img]

memphis · Postby **memphis** » Sun Nov 11, 2007 9:14

<div class='quotetop'>QUOTE (Stealth01 @ Nov 11 2007, 07:55 PM) [url=index.php?act=findpost&pid=10311]<{POST_SNAPBACK}>[/url]</div>

The good news is that they will be driving a 6i, so they won't be able to catch you to break your knees, and if they do, just threaten to scratch their car. They'll get scared. [img]http://coloradomazdaclub.com/forums/style_emoticons/<#EMO_DIR#>/smile.gif[/img][/b]

Sorry a lil off topic,, but stealth,, did you have to use a pic of all of our cars where Im the only car with the lights off cause your to slow to take a pic? LOL

OpacRX · Postby **OpacRX** » Sun Nov 11, 2007 9:14

<div class='quotetop'>QUOTE (Memphis @ Nov 11 2007, 08:49 PM) [url=index.php?act=findpost&pid=10312]<{POST_SNAPBACK}>[/url]</div>

Sorry a lil off topic,, but stealth,, did you have to use a pic of all of our cars where Im the only car with the lights off cause your to slow to take a pic? LOL[/b]

lol thread jacker!! j/k but back on topic thats a good thing to know if/when my engine goes out. is the guy in colorado?

Stealth01 · Postby **Stealth01** » Sun Nov 11, 2007 9:14

<div class='quotetop'>QUOTE (Memphis @ Nov 11 2007, 08:49 PM) [url=index.php?act=findpost&pid=10312]<{POST_SNAPBACK}>[/url]</div>

Sorry a lil off topic,, but stealth,, did you have to use a pic of all of our cars where Im the only car with the lights off cause your to slow to take a pic? LOL[/b]

LOL. I didn't even notice that. Of course, if you weren't too stingy to leave the engine running, then your lights would have stayed on!

<div class='quotetop'>QUOTE (OpacRX @ Nov 11 2007, 08:54 PM) [url=index.php?act=findpost&pid=10313]<{POST_SNAPBACK}>[/url]</div>

lol thread jacker!! j/k but back on topic thats a good thing to know if/when my engine goes out. is the guy in colorado?[/b]

Good to know since there seem to be a TON of older rotaries around here.

goldrocket · Postby **goldrocket** » Sun Nov 11, 2007 9:14

<div class='quotetop'>QUOTE </div>

lol thread jacker!! j/k but back on topic thats a good thing to know if/when my engine goes out. is the guy in colorado?[/b]

Nope, he's now in Nevada. But his prices are awesome and shipping was $300 when I sent mine to CA for him to build, so I imagine it will be a little cheaper to NV.
I was on the phone with him for a few minutes and they are going to give me all the tech info like port timing etc. when I start mapping my efi sysytem...when I put it together.

As for the thugs coming to my door, you better send more than two! LOL!!!

SpeedRacer · Postby **SpeedRacer** » Sun Nov 11, 2007 9:14

Wow thats really awesome thank you for sharing the info Gold!

goldrocket · Postby **goldrocket** » Mon Nov 12, 2007 9:14

That's what forums are for, sharing info. I'm just trying to be useful.

Postby **RX-7 Chris** » Tue Nov 13, 2007 9:14

That's good to know, I've been looking for a good shop that does not rip you a new one.

RX-7drifter · Postby **RX-7drifter** » Tue Nov 13, 2007 9:14

now hold up where is this shop at

Postby **RX-7 Chris** » Tue Nov 13, 2007 9:14

http://www.rotarywarehouse.com/index.php

371 HWY 395 South
Gardnerville, Nevada 89460

775-230-0133
916-617-6773

Monday - Friday: 8:00 AM - 6:00 PM
& Saturday: 9:00 AM - 4:00 PM
Sunday: Closed

Attention All Rotorheads!

Who is online