I've been following what's been provided here: http://goo.gl/gWMS1
And it's all good except for that wiring harness. I can NOT seem to get those posts off of the threaded studs.
I don't have the special tool, so I've been trying the tiny slotted screwdriver, moving the tab both toward and away from the stud, and even tried pulling on it with a pair of pliers.
Anyone have a little nugget of insight for me?
as for the one on the front side of the cover, I don't see ANYTHING to push, pull, or otherwise manipulate.
HELP! All I wanna do is change the valve cover gasket!
2.3L valve cover removal - Wiring harness. Grr.
- RedRoadster
- Posts: 641
- Joined: Fri Sep 21, 2007 9:14
- Location: Colorado Springs
- Contact:
2.3L valve cover removal - Wiring harness. Grr.
95 Classic Red Miata - 'Kona'
Racing Beat Sways, AEM WB O2 sensor, ACT clutch, Ground Control Springs, Bilstein HDs, Fat Cat bumpstops, 95 stock 14s (winter) or 99 sport 15s (summer)
Flyin' Miata stuff:
FM II Link GT2560R turbo, Butterfly brace, N/A dual exhaust, Oil filter relo kit, Rear shock mounts
08 Sunlight Silver Mazda 3s GT Sedan - 'Tuna'
OEM Wing spoiler, Sirius and Media switcher
05 Onyx Black Mazda 6i Hatchback - 'Smokey'
Racing Beat Sways, AEM WB O2 sensor, ACT clutch, Ground Control Springs, Bilstein HDs, Fat Cat bumpstops, 95 stock 14s (winter) or 99 sport 15s (summer)
Flyin' Miata stuff:
FM II Link GT2560R turbo, Butterfly brace, N/A dual exhaust, Oil filter relo kit, Rear shock mounts
08 Sunlight Silver Mazda 3s GT Sedan - 'Tuna'
OEM Wing spoiler, Sirius and Media switcher
05 Onyx Black Mazda 6i Hatchback - 'Smokey'
- AuroraAxela
- Posts: 397
- Joined: Wed Dec 14, 2011 9:14
- Location: Aurora, CO
They should just pry up. You're not going to break them, per se. They aren't threaded themselves, and will just push back on when reassembling.
[SIGPIC][/SIGPIC]
[color="Blue"][SIZE="3"]2009 Mazdaspeed 3 GT[/SIZE][/color]
[SIZE="1"][color="Blue"][color="Blue"]POWERTRAIN: GTX3067R . Cobb AP . Cobb 3-port . Autotech internals . HTP 3" intake . cp-e FMIC . Forge v1 BPV . TWM STS . CNT Turboback
NGK 1-step colder . Bosch 3-bar . cp-e xFlex™ RMM/TMM/PMM . CorkSport recirc tube . Kosmic EGR delete
SUSPENSION: K-Sport coilovers . Whiteline RSB . custom MS6 wheels
EXTERIOR: cp-e TowPlate . DDM Tuning 5000K HID low/fog
INTERIOR: Defi boost gauge/cp-e defroster mount . NRG shift knob . CorkSport LEDs[/color][/color][/SIZE]
NGK 1-step colder . Bosch 3-bar . cp-e xFlex™ RMM/TMM/PMM . CorkSport recirc tube . Kosmic EGR delete
SUSPENSION: K-Sport coilovers . Whiteline RSB . custom MS6 wheels
EXTERIOR: cp-e TowPlate . DDM Tuning 5000K HID low/fog
INTERIOR: Defi boost gauge/cp-e defroster mount . NRG shift knob . CorkSport LEDs[/color][/color][/SIZE]
- RedRoadster
- Posts: 641
- Joined: Fri Sep 21, 2007 9:14
- Location: Colorado Springs
- Contact:

The front side came off relatively easily. It won't snap back on, but I supose that's fine.
The back side broke off the plastic track across the top of the cover.
At that point I tried to pry it off and sliced myself up pretty good, so I took the hammer to it and just destroyed it off.
Good enough.
95 Classic Red Miata - 'Kona'
Racing Beat Sways, AEM WB O2 sensor, ACT clutch, Ground Control Springs, Bilstein HDs, Fat Cat bumpstops, 95 stock 14s (winter) or 99 sport 15s (summer)
Flyin' Miata stuff:
FM II Link GT2560R turbo, Butterfly brace, N/A dual exhaust, Oil filter relo kit, Rear shock mounts
08 Sunlight Silver Mazda 3s GT Sedan - 'Tuna'
OEM Wing spoiler, Sirius and Media switcher
05 Onyx Black Mazda 6i Hatchback - 'Smokey'
Racing Beat Sways, AEM WB O2 sensor, ACT clutch, Ground Control Springs, Bilstein HDs, Fat Cat bumpstops, 95 stock 14s (winter) or 99 sport 15s (summer)
Flyin' Miata stuff:
FM II Link GT2560R turbo, Butterfly brace, N/A dual exhaust, Oil filter relo kit, Rear shock mounts
08 Sunlight Silver Mazda 3s GT Sedan - 'Tuna'
OEM Wing spoiler, Sirius and Media switcher
05 Onyx Black Mazda 6i Hatchback - 'Smokey'
- speedjunkie
- Senior Member
- Posts: 5372
- Joined: Wed Jan 02, 2008 9:14
- Location: Colorado Springs
- Contact:
Actually, those are different. I did "destroy off" lots of clips though.
With the fasteners on the threaded posts, I actually just squeeze them with a pair of pliers and pull up. Squeeze on the sides with the tabs.
Anyone have an easy solution for removing an engine without a car hoist, or does anyone have a car hoist that won't be needed for a few days as I (well, another CMZC memeber) swaps an engine?
With the fasteners on the threaded posts, I actually just squeeze them with a pair of pliers and pull up. Squeeze on the sides with the tabs.
Anyone have an easy solution for removing an engine without a car hoist, or does anyone have a car hoist that won't be needed for a few days as I (well, another CMZC memeber) swaps an engine?
- speedjunkie
- Senior Member
- Posts: 5372
- Joined: Wed Jan 02, 2008 9:14
- Location: Colorado Springs
- Contact:
Who is online
Users browsing this forum: Bing [Bot] and 148 guests

